HOLPOSON? Color Keep-Rub
HOLPOSON? Color Keep-Rub 是本公司開發的濕摩擦牢度提高劑，適用于棉及纖維素纖維采用活性、直接、還原以及硫化染料浸染織物、成衣服裝的摩擦牢度提高。尤其適用于黑色、大紅色等顏色的牢度提高。
一、物化性能
外 觀 淡黃色液體
離子性 弱陽離子
PH 酸性
溶解性 易稀釋于冷水中
二、使用方法
1.浸軋法
HOLPOSON? Color Keep-Rub 20~30g/L
分散螯合劑 0.5g/L（有助于穩定）
醋酸調節 pH=5
加工方法 一浸一軋 軋液率70%， 烘干后焙烘150度*60~90秒
2. 浸漬法加工工藝
HOLPOSON? Color Keep-Rub 2~5g/L
加工方法 30~40度* 5~10 分鐘后，脫水，烘干。
產品性能
1. 顯著提高活性、直接染料、硫化、還原染料染色物的濕摩擦牢度。
2. 幾乎不影響染色物的色光和手感。
3. 具有良好的穩定性，適用于針織物、成衣浸漬處理。
注意事項
1. 請配液濃度需控制在30g/L以下,用冷水稀釋溶解，溶解水溫不超過35℃。
2. 處理前的染色物務必充分水洗去除浮色，并中和調節布面 pH 值至中性~弱酸性。
3. 由于浸染設備不同，加工中工作液會受到不同程度的剪切而影響穩定性，務必實際加工前通過預備試驗確保產品穩定性后使用。
4. 本產品為弱陽離子，也會受到印染加工中使用水的硬度、金屬離子、酸、堿、鹽等因素而影響其穩定性，務請通過小樣試驗確認和同浴使用的其它藥劑的相容穩定性
貯 存
室內存放，避免高溫、嚴寒。
Color Fastness to Wet Friction Promoter for Reactive Dyes
HOLPOSON? Color Keep-Rub
Color Keep-Rub is a color fastness to wet friction improver developed by our company. It’s suitable for improving the color fastness to friction of textiles made of cotton and cellulosic fibers, which are dyed with reactive, direct, reductive and sulfurized dyes. It is especially suitable for improving the fastness of black, bright red and other colors.
Physical & chemical properties:
Appearance: Light yellow liquid
Ionicity: Weak cationic
pH: Acidic
Solubility: Easily dilutable in cold water
Usage:
1. Padding
Color Keep-Rub: 20~30g/L
Dispersing chelator: 0.5g/L (for stability)
Acetic acid adjustment: pH = 5
Processing method: Dip and roll (liquid content: 70%), bake at 150℃ for 60 - 90 seconds after drying
2. Impregnation process
Color Keep-Rub: 2~5g/L
Processing method: Impregnate at 30-40℃ for 5-10 minutes, dehydrate and dry.
Characteristics:
1. Significantly improves the color fastness to wet friction of materials dyed with reactive, direct, sulfurized and reduced dyes.
2. It hardly affects the luster and hand feeling of the dyed material.
3. It has good stability and is suitable for impregnation treatment of knitted fabric and finished garment.
Attentions:
Please control the concentration of the solution below 30g/L, dilute it with cold water with a temperature of no more than 35 ℃.
Before treatment, the material must be fully washed to remove flooding, and adjust by neutralization the pH value of fabric surface to neutral - weak acidic.
Due to different dyeing equipment, the operation stability will be affected by possib